MD4C VACUUBRAND Vacuum Pump Composite Diaphragm Repair Kit, 90 mm OD × 10 mm Bore

MD4C VACUUBRAND Vacuum Pump Composite Diaphragm Repair Kit, 90 mm OD × 10 mm Bore. Confirm fitment before ordering.

Request a Quote

SKU: MD4C Category:

Description

MD4C VACUUBRAND Vacuum Pump Composite Diaphragm Repair Kit, 90 mm OD × 10 mm Bore. Match the original part to the required equipment configuration before requesting a replacement.

Request a Quote

Technical Data

Confirm the full model, the original part markings and the installed dimensions before ordering. Parts or configurations shown together are not necessarily interchangeable.

Component and Equipment Reference

Series reference only. Fitment to the listed replacement is not independently verified. VACUUBRAND MD 4C NT; fitment to MD4C 90/10 mm replacement unconfirmed. Equipment ratings are not replacement-part ratings.

MD 4C NT Pump Family Reference

Parameter MD 4C NT
Pumping speed 50 / 60 Hz 3.4 / 3.8 m³/h
Ultimate vacuum without / with gas ballast 1.5 / 3 mbar absolute
Stages 3
Approximate dimensions 328 × 243 × 198 mm
Approximate mass 14.3 kg

MD 4C NT Family Wetted Materials

Component Material
Head cover / diaphragm clamping disc Carbon-reinforced ETFE
Diaphragm PTFE
MD 4C NT group valves FFKM
O-rings FKM
Valve block Carbon-reinforced ECTFE
Gas ballast tube / pump nozzles Carbon-reinforced PTFE
Flexible tubing / flow-control diaphragm PTFE
Separator / condenser flask Borosilicate glass

MD 4C NT Family Maintenance Reference

Operation Recommended Interval
Clean surfaces and fan grille As required
Replace diaphragms, valves and O-rings 15,000 operating hours, application-dependent
Clean / replace PTFE tubing As required
Replace motor capacitors 10,000–40,000 hours or reduced performance

MD 4C NT Seal-Kit Reference — Confirm Fitment

Equipment Group Seal-Kit Order Code Fitment Boundary
MD 4C NT / PC 201 NT / ME 8C NT +2AK 20696870 Complete seal kit; not a verified code for the pictured 90 mm / 10 mm loose diaphragm

Maintenance and Wear Components

Diaphragms, valves and motor capacitors are wear components. Bearings are encapsulated and lubricated for life. Clean pumping chambers, diaphragms and valves if vacuum performance deteriorates or noise increases; aggressive vapours or deposits can require shorter service intervals. Match the complete NT or non-NT model and head configuration before ordering.

Diaphragm Service Reference

Inspect diaphragms for contamination or damage and avoid sharp tools. Retain the original quantity and thickness of each head’s spacer washers; too few impair vacuum and too many cause knocking. Install the light diaphragm side toward the clamping disc. The MD 4C NT service instructions specify 6 Nm diaphragm torque and 12 Nm head-screw torque, tightened diagonally. These procedures apply to the specified NT equipment, not every MD4C replacement.

Post-Service Check

Check ultimate vacuum after maintenance; several hours of running-in may be necessary after diaphragm or valve replacement. The listed 90 mm outside diameter and 10 mm bore must be matched to the actual part; the NT family data do not prove interchangeability with the shortened MD4C reference.

Selection and Inquiry

Send the equipment nameplate, complete model, measurements and quantity. Check fastening, material and service conditions against the original part.

Request a Quote

Browse Pump Repair Kits.

Installation Preparation

Prepare the equipment according to the site procedure and the manufacturer's instructions before installing this part. Where relevant, isolate power and pressure sources, then check the mounting direction, connection points, and sealing arrangement. After installation, inspect the completed connections before beginning a controlled functional test.

International Delivery Options

We can discuss international delivery arrangements according to the order and destination. FedEx, UPS, DHL, or another suitable express service may be considered based on the shipment requirements. Please provide the delivery location and product details during the enquiry so that the available shipping arrangement can be confirmed before the order is processed.