IMI Norgren 0821097 8D G1/4 Electro-Mechanical Hydraulic Pressure Switch
IMI Norgren 0821097 is an 8D electro-mechanical hydraulic pressure switch with G1/4 connection and a 50-250 bar range for neutral liquid fluids.
Description
IMI Norgren 0821097 is an 8D electro-mechanical hydraulic pressure switch with G1/4 connection and a 50-250 bar range for neutral liquid fluids.
Key Features
- Model: 0821097
- Model: 0821097
- Pressure port: G1/4
- Switching range: 50-250 bar
Technical Data
| Model | 0821097 |
|---|---|
| Model | 0821097 |
| Pressure port | G1/4 |
| Switching range | 50-250 bar |
| Connection | Pg 13.5 cable gland |
Selection and Installation
Compare the complete part code, mounting arrangement and relevant operating requirements with the existing equipment before ordering. Isolate pressure and electrical supplies as applicable before replacement, and follow the machine manufacturer’s installation procedure.
Inquiry
Send the complete part number, required quantity and clear photos of the current part for version and availability confirmation.
0821097 Exact Model Data
| Parameter | Value |
|---|---|
| Pressure range | 50-250 bar (725-3625 psi) |
| Pressure port | G1/4 |
| Switching difference, lower / upper range | 12 / 16 bar |
| Electrical connection | Cable gland, Pg 13.5 |
| Body / seal | Aluminium / FPM-PTFE |
| Drawing | 1 |
8D Hydraulic Operating Conditions
| Parameter | Value |
|---|---|
| Medium | Neutral liquid fluids |
| Operating principle | Diaphragm |
| Repeatability | +/-2% of final value, depending on regulating pressure |
| Hysteresis | Fixed |
| Switching rate | 20 cycles/min |
| Maximum viscosity | 1000 mm^2/s |
| Ambient temperature | -10 to +80 degrees C |
| Media temperature | 0 to +80 degrees C |
| Protection | IP64 for specified Form A and cable-gland configurations |
| Mass | 0.4 kg |
8D Silver-Contact Switching Capacity
| Voltage | AC resistive | AC inductive, cos phi 0.7 | DC resistive | DC inductive, L/R approximately 10 ms |
|---|---|---|---|---|
| 24 V | 5 A | 4 A | 2 A | 1 A |
| 60 V | 5 A | 2.5 A | 0.9 A | 0.3 A |
| 110 V | 5 A | 1.5 A | 0.45 A | 0.09 A |
| 230 V | 5 A | 0.9 A | 0.2 A | 0.02 A |
0821097 Drawing 1 Reference
| Parameter | Value |
|---|---|
| Height | Approximately 135 mm |
| Width | 33 mm |
| Side extent | 72.5 mm |
| Mounting holes | Diameter 5.3 mm |
| Connection labels | G1/4 and Pg 13.5 |
Liquid-Service Selection
This is the hydraulic 8D version for neutral liquid fluids. Do not transfer the operating range from a pneumatic 8D or another pressure option.
Setpoint and Hysteresis
Setpoints should ideally be near the middle of the range. Switching pressure must remain within the listed range; the switching difference is fixed.
Contact Load and Temperature
Current ratings are referenced to +30 degrees C. At +70 degrees C permissible current is 50% of the tabulated value; inductive loads require suitable suppression.
Mounting and Wiring
Check the drawing for vertical mounting and bottom pressure-port access. The Form A terminal diagram should not be assumed to specify the cable-gland version's wiring.
Functional Check After Replacement
After fitting the replacement, follow the equipment commissioning procedure before returning the machine to normal operation. Where applicable, test under controlled conditions and observe response, movement, signals, leakage, and connection stability. Check the installation again after its initial run to identify any adjustment that may be needed.
Payment Arrangements
The payment method is confirmed as part of the order arrangement. International orders may be settled in USD by T/T, PayPal, or another mutually agreed method. For payments in RMB within mainland China, Alipay QR code and WeChat Pay QR code arrangements are also available. The applicable option is agreed before order processing.
Additional information
| Model | 0821097 |
|---|---|
| Order code | 0821097 |
| Pressure port | G1/4 |
| Switching range | 50-250 bar |
| Connection | Pg 13.5 cable gland |








