FESTO CPE10-M1BH-3GL-M7 196915 Solenoid Valve

The FESTO CPE10-M1BH-3GL-M7, part number 196915, is a solenoid valve. The supplied Festo datasheet confirms this product identity and lists its model-specific technical data below.

SKU: CPE10-M1BH-3GL-M7 Category: Tags: , , Brand:

Description

FESTO CPE10-M1BH-3GL-M7 196915 Solenoid Valve

The FESTO CPE10-M1BH-3GL-M7, part number 196915, is a solenoid valve. The supplied Festo datasheet confirms this product identity and lists its model-specific technical data below.

Key Features

  • Valve function: 3/2-way, single solenoid, closed.
  • Type of actuation: Electrical.
  • Construction width: 10 mm.

Technical Data

Brand FESTO
Model CPE10-M1BH-3GL-M7
Part number 196915
Product type Solenoid Valve
Valve function 3/2-way, single solenoid, closed
Type of actuation Electrical
Construction width 10 mm
Standard nominal flow rate (standardised to DIN 1343) 400 l/min
pneumatic working port M7
Operating voltage 24 V DC
Operating pressure 0.25 MPa … 0.8 MPa
Operating pressure 2.5 bar … 8 bar
Design Piston gate valve
Type of reset Pneumatic spring
Degree of protection IP65 With plug socket To IEC 60529
Nominal size 4 mm
Sealing principle Soft
Mounting position Any
Manual override Detenting via accessory Non-detenting
Type of piloting Piloted
Pilot air supply Internal
Flow direction Non-reversible
Valve position code Label holder
lap Overlap
Switching time off 14 ms
Switching time on 14 ms
Duty cycle 100% in conjunction with holding current reduction
Max. positive test pulse with 0 signal 1200 µs
Max. negative test pulse with 1 signal 900 µs
Characteristic coil data 24 V DC: 1.28 W
Permissible voltage fluctuations -15% / +10%
Operating medium Compressed air to ISO 8573-1:2010 [7:4:4]
Note on operating and pilot medium Lubricated operation possible (in which case lubricated operation will always be required)
Vibration resistance Transport application test with severity level 2 to FN 942017-4 and EN 60068-2-6
Shock resistance Shock test with severity level 2 to FN 942017-5 and EN 60068-2-27
Corrosion resistance class CRC 2 – Moderate corrosion stress
Media temperature -5 °C … 50 °C
Ambient temperature -5 °C … 50 °C
Product weight 40 g
Electrical connection 2-pin
Type of mounting With through-hole
Pilot exhaust port 82 M3
Pilot air port 12 M3
Pneumatic connection, port 1 M7
Pneumatic connection, port 2 M7
Pneumatic connection, port 3 M7
Material seals NBR
Material housing Die-cast aluminium

Application Notes

Confirm the complete model and part number against the existing equipment. Products in the same Festo series may have different dimensions, connections and operating configurations.

Selection and Installation

Check the equipment documentation and the applicable Festo installation instructions before replacement or commissioning.

Inquiry

For a quotation, provide model CPE10-M1BH-3GL-M7, part number 196915, required quantity and destination.

Exact-Model Datasheet Check

The supplied Festo datasheet identifies CPE10-M1BH-3GL-M7 as a solenoid valve under part number 196915. It lists valve function as 3/2-way, single solenoid, closed. Confirm the full variant before ordering.

Installation Preparation

Prepare the equipment according to the site procedure and the manufacturer's instructions before installing this part. Where relevant, isolate power and pressure sources, then check the mounting direction, connection points, and sealing arrangement. After installation, inspect the completed connections before beginning a controlled functional test.

Product Inquiry Support

We assist customers with industrial automation spare-part enquiries, including model confirmation, replacement questions, and initial photo comparisons. If you are unsure which version is installed, you may send the complete model code and clear photos of the nameplate or component. We will use the information provided to help review the enquiry and identify details that still need confirmation.

Additional information

Brand

FESTO

Model

CPE10-M1BH-3GL-M7

Part number

196915

Product type

Solenoid Valve

Valve function

3/2-way, single solenoid, closed

Type of actuation

Electrical

Construction width

10 mm

Standard nominal flow rate (standardised to DIN 1343)

400 l/min

pneumatic working port

M7

Operating voltage

24 V DC

Operating pressure

2.5 bar … 8 bar