FESTO MHA1-2X2/2G-1,5-4-4-4 566175 Vacuum Valve

The FESTO MHA1-2X2/2G-1,5-4-4-4, part number 566175, is a vacuum valve. The supplied Festo datasheet confirms this product identity and lists its model-specific technical data below.

SKU: MHA1-2X2/2G-1,5-4-4-4 Category: Tags: , , Brand:

Description

FESTO MHA1-2X2/2G-1,5-4-4-4 566175 Vacuum Valve

The FESTO MHA1-2X2/2G-1,5-4-4-4, part number 566175, is a vacuum valve. The supplied Festo datasheet confirms this product identity and lists its model-specific technical data below.

Key Features

  • Valve function: 2×2/2 closed monostable.
  • Type of actuation: Electrical.
  • Construction width: 20 mm.

Technical Data

Brand FESTO
Model MHA1-2X2/2G-1,5-4-4-4
Part number 566175
Product type Vacuum Valve
Valve function 2×2/2 closed monostable
Type of actuation Electrical
Construction width 20 mm
Standard nominal flow rate (standardised to DIN 1343) 30 l/min
pneumatic working port QS-4
Operating voltage 24 V DC
Operating pressure 0 bar … 1.5 bar
Type of reset Mechanical spring
Degree of protection IP40
Nominal size 1.5 mm
Grid dimension 20 mm
Exhaust-air function Cannot be throttled
Sealing principle Soft
Mounting position Any
Manual override Non-detenting
Type of piloting Direct
Flow direction Non-reversible
lap Underlap
Signal status display LED
Operating pressure, reversible -0.95 bar … 0 bar
Suitability for vacuum Yes
Standard flow rate (standardised to DIN 1343) 30 l/min
Max. switching frequency 10 Hz
Switching time off 6 ms
Switching time on 6 ms
Duty cycle 100%
Characteristic coil data 24 V DC: low-current phase 0.7 W, high-current phase 3.0 W
Permissible voltage fluctuations +/-10%
Operating medium Compressed air to ISO 8573-1:2010 [7:4:4]
Note on operating and pilot medium Lubricated operation possible (in which case lubricated operation will always be required)
Vibration resistance Transport application test with severity level 2 to FN 942017-4 and EN 60068-2-6
Shock resistance Shock test with severity level 2 to FN 942017-5 and EN 60068-2-27
Corrosion resistance class CRC 2 – Moderate corrosion stress
Storage temperature -20 °C … 60 °C
Media temperature -5 °C … 50 °C
Ambient temperature -5 °C … 50 °C
Product weight 30.6 g
Max. cable length 30 M
Electrical connection Plug KMH
Type of mounting With through-hole
Pneumatic connection, port 1 QS-4
Pneumatic connection, port 11 QS-4
Pneumatic connection, port 2 QS-4
Material seals Fluoro rubber HNBR NBR
Material housing Reinforced PPS
Material screws Steel

Application Notes

Confirm the complete model and part number against the existing equipment. Products in the same Festo series may have different dimensions, connections and operating configurations.

Selection and Installation

Check the equipment documentation and the applicable Festo installation instructions before replacement or commissioning.

Inquiry

For a quotation, provide model MHA1-2X2/2G-1,5-4-4-4, part number 566175, required quantity and destination.

Exact-Model Datasheet Check

The supplied Festo datasheet identifies MHA1-2X2/2G-1,5-4-4-4 as a vacuum valve under part number 566175. It lists valve function as 2×2/2 closed monostable. Confirm the full variant before ordering.

Installation Preparation

Prepare the equipment according to the site procedure and the manufacturer's instructions before installing this part. Where relevant, isolate power and pressure sources, then check the mounting direction, connection points, and sealing arrangement. After installation, inspect the completed connections before beginning a controlled functional test.

Payment Arrangements

The payment method is confirmed as part of the order arrangement. International orders may be settled in USD by T/T, PayPal, or another mutually agreed method. For payments in RMB within mainland China, Alipay QR code and WeChat Pay QR code arrangements are also available. The applicable option is agreed before order processing.

Additional information

Brand

FESTO

Model

MHA1-2X2/2G-1,5-4-4-4

Part number

566175

Product type

Vacuum Valve

Valve function

2×2/2 closed monostable

Type of actuation

Electrical

Construction width

20 mm

Standard nominal flow rate (standardised to DIN 1343)

30 l/min

pneumatic working port

QS-4

Operating voltage

24 V DC

Operating pressure

0 bar … 1.5 bar

Type of reset

Mechanical spring