FESTO ADN-12-25-I-P-A 536215 Compact Pneumatic Cylinder
FESTO ADN-12-25-I-P-A is a double-acting compact pneumatic cylinder with a 12 mm bore and 25 mm stroke. Part number 536215, it is based on ISO 21287 and is suitable for compact pneumatic automation assemblies requiring reliable linear motion.
Please include the model, quantity, destination, and any required technical details.
Description
The FESTO ADN-12-25-I-P-A, part number 536215, is a compact double-acting pneumatic cylinder from the ADN series. Its 12 mm piston diameter and 25 mm stroke make it suitable for space-conscious automation equipment where repeatable linear motion is required.
This version is based on ISO 21287 and uses elastic cushioning rings or plates at both end positions. It has a piston rod at one end with a female M3 thread. Position sensing can be used with a compatible proximity sensor.
Key Features
- FESTO ADN compact cylinder, part number 536215
- Double-acting pneumatic operation
- 12 mm piston diameter and 25 mm stroke
- ISO 21287 design
- Elastic cushioning at both end positions
- Female M3 piston-rod thread and M5 pneumatic connection
- Suitable for proximity-sensor position detection
Technical Data
| Brand | FESTO |
|---|---|
| Series | ADN |
| Model | ADN-12-25-I-P-A |
| Part Number | 536215 |
| Mode of Operation | Double-acting |
| Piston Diameter | 12 mm |
| Stroke | 25 mm |
| Operating Pressure | 1 to 10 bar |
| Pneumatic Connection | M5 |
| Piston Rod Thread | M3 female |
| Ambient Temperature | -20 to 80 C |
| Standard | ISO 21287 |
Application Notes
This compact cylinder can be considered for clamping, positioning, part handling, and other compact linear-motion tasks in pneumatic automation equipment. Its short body design is useful where machine builders need a defined stroke but have limited installation space. Typical examples include small assembly fixtures, transfer mechanisms, pick-and-place tooling, packaging equipment, and workholding devices.
Selection and Sizing for FESTO ADN-12-25-I-P-A
Choose the cylinder from the required movement first, then confirm the available air pressure and the load on the piston rod. The 25 mm stroke should match the required travel after allowing for end-position clearance and the mechanics of the tooling. At 6 bar, the theoretical force is approximately 68 N in the advance direction and 51 N in the return direction. Actual available force will be lower once friction, side load, acceleration, and the connected mechanism are considered.
Confirm that the M5 pneumatic ports are suitable for the fittings and tube size used in the machine. A restriction in the valve, fitting, or tube can reduce cylinder speed even when the nominal operating pressure is adequate. For fast or frequent cycles, review the full air path together with the required cycle time instead of selecting the cylinder only by bore and stroke.
Mounting and Sensor Considerations
The piston rod has a female M3 thread, so the mating linkage or accessory should be selected to match the intended load path. The cylinder should be mounted so that the rod is not subjected to unnecessary lateral force. Side loading can increase seal wear and may affect smooth motion or service life.
This model is suitable for position detection with a compatible proximity sensor. When an end-position signal is needed for machine control, confirm the sensor type, cable connection, switching logic, and available mounting location before ordering. The cylinder sensor provides position feedback; it does not replace mechanical guarding or safety functions in the machine design.
Air Quality and Maintenance
Clean, adequately prepared compressed air helps pneumatic components operate consistently. Use an air preparation arrangement appropriate for the installation and keep the supply within the specified 1 to 10 bar operating range. If lubricated compressed air is introduced into operation, lubrication must then be maintained for subsequent operation. Before replacement or installation, compare the product label, mounting dimensions, configuration, and current manufacturer documentation with the equipment requirement.
Inquiry
Contact YOUPH Automation with the model ADN-12-25-I-P-A, part number 536215, required quantity, destination, and technical requirements for availability and quotation support.
Additional information
| Brand | FESTO |
|---|---|
| Model | ADN-12-25-I-P-A |
| Part Number | 536215 |
| Cylinder Type | Compact pneumatic cylinder |
| Operation | Double-acting |
| Piston Diameter | 12 mm |
| Stroke | 25 mm |
| Operating Pressure | 1 to 10 bar |
| Pneumatic Connection | M5 |
| Piston Rod Thread | M3 female |
| Standard | ISO 21287 |





