FESTO CMMS-ST-C8-7 547454 Motor Controller
The Festo CMMS-ST-C8-7 is a motor controller for a stepper motor. The datasheet lists a 48 V DC nominal load supply, 8 A nominal load-supply current and a separate 24 V DC logic supply.
Description
FESTO CMMS-ST-C8-7 547454 Motor Controller
The Festo CMMS-ST-C8-7 is a motor controller for a stepper motor. The datasheet lists a 48 V DC nominal load supply, 8 A nominal load-supply current and a separate 24 V DC logic supply.
Key Features
- 48 V DC nominal load supply
- 8 A nominal load-supply current
- 24 V DC logic supply
- Micro-step operating mode with encoder sensing
Technical Data
| Brand | FESTO |
|---|---|
| Model | CMMS-ST-C8-7 |
| Part number | 547454 |
| Controller operating mode | PWM-MOSFET power output stage |
| Operating mode | Micro step, >4000 step/U |
| Adjustable current reduction | Using software |
| Position sensor | Encoder |
| Mains filter | Integrated |
| Step adjustment | Using software |
| Protective function | I²t monitoring Temperature monitoring Current monitoring Voltage failure detection Drag error monitoring |
| Rotor position sensor | Encoder |
| Display | Seven-segment display |
| Control elements | DIP switch |
| Nominal current adjustment | Using software |
| Max. step frequency | 4 kHz |
| Braking resistance | 17 Ohm |
| Bus terminating resistor | Integrated |
| Digital logic output characteristics | Freely configurable to a given extent Not electrically isolated |
| Setpoint input impedance | 20 kOhm |
| Braking resistance pulse power | 0.5 kVA |
| Max. current, digital logic outputs | 100 mA |
| Max. peak current duration | 2 s |
| Max. intermediate circuit voltage, DC | 48 V |
| Nominal DC voltage, logic power supply | 24 V |
| Nominal voltage, load supply DC | 48 V |
| Nominal current, load supply | 8 A |
| Nominal current, logic supply | 0.3 A |
| Parameters configuring interface | RS232 (9600…115000 Bits/s) |
| Peak current, load supply | 12 A |
| Permissible range, logic voltage | ± 20 % |
| Storage temperature | -25 … 70 °C |
| Relative air humidity | 0 – 90 % non-condensing |
| Protection class | IP20 |
| Ambient temperature | 0 … 50 °C |
| Product weight | 2,000 g |
| Number of analogue monitor outputs | 1 |
| Number of analogue setpoint inputs | 1 |
| Monitor output working range | ± 10 V |
| Setpoint input working range | ± 10 V |
| Encoder interface input, characteristics | RS422 |
| Encoder interface output, function | Setpoint specification for downstream slave drive unit |
| Encoder interface input, function | In synchronous operation as specified speed in RPM for the slave drive unit |
| Bus connection | CAN interface D-Sub 9-pin |
| Fieldbus coupling | CANopen Profibus DP |
| Mounting type | Tightened On sub-base |
Application Notes
Confirm the complete model code, the installed mechanical or electrical interface and the operating limits against the original equipment. Similar products within a series can differ in pressure, supply, output, mounting or communication.
Selection and Installation
Compare the original nameplate, the part number and the product-specific datasheet. Follow Festo and machine manufacturer instructions for mounting, connections and controlled commissioning. Clarify any uncertain option or suffix before ordering.
Inquiry
For a quotation or replacement enquiry, provide model CMMS-ST-C8-7, part number 547454, quantity, destination and clear photos of the original unit when available.
Separate Load and Logic Supplies
The CMMS-ST-C8-7 datasheet lists a 48 V DC nominal load supply and a separate 24 V DC nominal logic supply. Confirm both circuits and the installed stepper-motor wiring before replacement.
Functional Check After Replacement
After fitting the replacement, follow the equipment commissioning procedure before returning the machine to normal operation. Where applicable, test under controlled conditions and observe response, movement, signals, leakage, and connection stability. Check the installation again after its initial run to identify any adjustment that may be needed.
Order Detail Confirmation
To help prepare an accurate spare-parts order, please include the full model code, required quantity, and delivery destination in your enquiry. Photos or existing purchase records may be useful when a suffix or replacement choice is uncertain. Product details, payment method, and shipping arrangement can then be reviewed together before order processing.
Additional information
| Brand | FESTO |
|---|---|
| Model | CMMS-ST-C8-7 |
| Part Number | 547454 |
| Controller operating mode | PWM-MOSFET power output stage |
| Operating mode | Micro step, >4000 step/U |
| Adjustable current reduction | Using software |
| Position sensor | Encoder |
| Mains filter | Integrated |
| Step adjustment | Using software |
| Protective function | I²t monitoring Temperature monitoring Current monitoring Voltage failure detection Drag error monitoring |
| Rotor position sensor | Encoder |









