MD4C VACUUBRAND Vacuum Pump Composite Diaphragm Repair Kit, 90 mm OD × 10 mm Bore
MD4C VACUUBRAND Vacuum Pump Composite Diaphragm Repair Kit, 90 mm OD × 10 mm Bore. Confirm fitment before ordering.
Description
MD4C VACUUBRAND Vacuum Pump Composite Diaphragm Repair Kit, 90 mm OD × 10 mm Bore. Match the original part to the required equipment configuration before requesting a replacement.
Technical Data
Confirm the full model, the original part markings and the installed dimensions before ordering. Parts or configurations shown together are not necessarily interchangeable.
Component and Equipment Reference
Series reference only. Fitment to the listed replacement is not independently verified. VACUUBRAND MD 4C NT; fitment to MD4C 90/10 mm replacement unconfirmed. Equipment ratings are not replacement-part ratings.
MD 4C NT Pump Family Reference
| Parameter | MD 4C NT |
|---|---|
| Pumping speed 50 / 60 Hz | 3.4 / 3.8 m³/h |
| Ultimate vacuum without / with gas ballast | 1.5 / 3 mbar absolute |
| Stages | 3 |
| Approximate dimensions | 328 × 243 × 198 mm |
| Approximate mass | 14.3 kg |
MD 4C NT Family Wetted Materials
| Component | Material |
|---|---|
| Head cover / diaphragm clamping disc | Carbon-reinforced ETFE |
| Diaphragm | PTFE |
| MD 4C NT group valves | FFKM |
| O-rings | FKM |
| Valve block | Carbon-reinforced ECTFE |
| Gas ballast tube / pump nozzles | Carbon-reinforced PTFE |
| Flexible tubing / flow-control diaphragm | PTFE |
| Separator / condenser flask | Borosilicate glass |
MD 4C NT Family Maintenance Reference
| Operation | Recommended Interval |
|---|---|
| Clean surfaces and fan grille | As required |
| Replace diaphragms, valves and O-rings | 15,000 operating hours, application-dependent |
| Clean / replace PTFE tubing | As required |
| Replace motor capacitors | 10,000–40,000 hours or reduced performance |
MD 4C NT Seal-Kit Reference — Confirm Fitment
| Equipment Group | Seal-Kit Order Code | Fitment Boundary |
|---|---|---|
| MD 4C NT / PC 201 NT / ME 8C NT +2AK | 20696870 | Complete seal kit; not a verified code for the pictured 90 mm / 10 mm loose diaphragm |
Maintenance and Wear Components
Diaphragms, valves and motor capacitors are wear components. Bearings are encapsulated and lubricated for life. Clean pumping chambers, diaphragms and valves if vacuum performance deteriorates or noise increases; aggressive vapours or deposits can require shorter service intervals. Match the complete NT or non-NT model and head configuration before ordering.
Diaphragm Service Reference
Inspect diaphragms for contamination or damage and avoid sharp tools. Retain the original quantity and thickness of each head’s spacer washers; too few impair vacuum and too many cause knocking. Install the light diaphragm side toward the clamping disc. The MD 4C NT service instructions specify 6 Nm diaphragm torque and 12 Nm head-screw torque, tightened diagonally. These procedures apply to the specified NT equipment, not every MD4C replacement.
Post-Service Check
Check ultimate vacuum after maintenance; several hours of running-in may be necessary after diaphragm or valve replacement. The listed 90 mm outside diameter and 10 mm bore must be matched to the actual part; the NT family data do not prove interchangeability with the shortened MD4C reference.
Selection and Inquiry
Send the equipment nameplate, complete model, measurements and quantity. Check fastening, material and service conditions against the original part.
Browse Pump Repair Kits.
Installation Preparation
Prepare the equipment according to the site procedure and the manufacturer's instructions before installing this part. Where relevant, isolate power and pressure sources, then check the mounting direction, connection points, and sealing arrangement. After installation, inspect the completed connections before beginning a controlled functional test.
International Delivery Options
We can discuss international delivery arrangements according to the order and destination. FedEx, UPS, DHL, or another suitable express service may be considered based on the shipment requirements. Please provide the delivery location and product details during the enquiry so that the available shipping arrangement can be confirmed before the order is processed.









