TX70 6-050-15-1 1-Inch Air-Operated Diaphragm Pump 145 mm Corrosion-Resistant Composite Diaphragm

TX70 6-050-15-1 1-Inch Air-Operated Diaphragm Pump 145 mm Corrosion-Resistant Composite Diaphragm. Confirm fitment before ordering.

Request a Quote

SKU: 6-050-15-1 Category:

Description

TX70 6-050-15-1 1-Inch Air-Operated Diaphragm Pump 145 mm Corrosion-Resistant Composite Diaphragm. Match the original part to the required equipment configuration before requesting a replacement.

Request a Quote

Technical Data

Confirm the full model, the original part markings and the installed dimensions before ordering. Parts or configurations shown together are not necessarily interchangeable.

Component and Equipment Reference

Series reference only. Fitment to the listed replacement is not independently verified. Tapflo T70 / TX70 metal-series pumps; listed replacement code and dimensions unconfirmed. Equipment ratings are not replacement-part ratings.

Tapflo Size-70 Diaphragm and Associated Parts Reference

Position Component Quantity per Pump Material / Selection Note
15 Diaphragm 2 EPDM, PTFE, NBR; FKM option for specified size-70 variants
16 Diaphragm shaft 1 AISI 316
36 Centre-block sealing 4 aluminium/cast iron; 2 stainless PE
47 Backup O-rings 4 aluminium/cast iron; 2 stainless, size-70 NBR standard; EPDM / FKM options

Tapflo Size-70 Complete-Pump Reference

Parameter Size-70 Family Rating
Maximum capacity 78 L/min
Volume per stroke 87.5 mL with EPDM; approximately 15% lower with PTFE
Maximum discharge / air pressure 8 bar / 8 bar
Maximum dry / wet suction lift 3 m / 8 m
Maximum solids size 4 mm
Temperature range Minimum −20 °C; maximum 80 °C EPDM/NBR or 110 °C PTFE, subject to compatibility
Aluminium / cast iron / stainless mass 5 / 10 / 7 kg, standard configurations
Housing torque, aluminium/cast iron / stainless 12 / 8 Nm

Tapflo Size-70 Connection Reference

Drawing Reference Value Selection Boundary
J 3/4 inch Complete-pump connection, not the listed 1-inch claim
J2 1/2 inch Different drawing option
L 1/4 inch Air connection drawing reference
A / B 150 / 168 mm Assembly drawing dimensions, not diaphragm diameter

Tapflo Family Troubleshooting Relevant to Diaphragms

Symptom Checks
Pump fails to run Air pressure, blocked air connection/muffler, air valve, chamber contamination, diaphragm damage
Poor suction Suction leakage/blockage, muffler, damaged or blocked valve balls
Irregular running / poor flow Valve balls, air valve, centre-block seals, air supply, entrained air, diaphragm condition
Liquid at muffler Diaphragm damage
Liquid leaking from casing Housing fastener torque

Installation and Air Supply Reference

Use supported piping, a short airtight reinforced suction line and flexible discharge piping. Supply clean oil-free air through a 5 µm or finer filter and regulator. Flooded inlet pressure should not exceed 0.7 bar. For submerged service, verify compatibility and route exhaust above the liquid. Maximum supply air is 8 bar; these are complete-pump requirements.

Diaphragm Maintenance

Drain and clean or neutralise the pump, disconnect air and isolate suction/discharge before dismantling. Remove one diaphragm and withdraw the opposing diaphragm with the shaft. On assembly, install shaft seals and backup O-rings, secure the shaft pin and align diaphragm holes. Tighten housing fasteners evenly and test-run. Confirm construction-specific torque and maintenance instructions.

Replacement Selection and Operating Boundary

Specify the complete nameplate pump code, position number and quantity. Position 15 is the diaphragm; EPDM, NBR, PTFE and certain FKM versions are distinct selections. Wear set 1 covers liquid-side parts and set 2 includes liquid- and air-side parts. The listed 6-050-15-1 reference, 145 mm diameter and 1-inch wording require confirmation; the size-70 family connection drawing lists 3/4-inch and 1/2-inch options. Running at roughly half maximum capacity reduces wear; avoid prolonged dry running or continuous maximum cycling.

Selection and Inquiry

Send the equipment nameplate, complete model, measurements and quantity. Check fastening, material and service conditions against the original part.

Request a Quote

Browse Pump Repair Kits.

Spare Parts Records

Keeping a clear record of installed components can make future maintenance and purchasing more efficient. For this product, record the brand, full model code, important specifications, and equipment location. Update the record whenever a component or machine configuration changes, so the next replacement decision is based on current information.

Order Detail Confirmation

To help prepare an accurate spare-parts order, please include the full model code, required quantity, and delivery destination in your enquiry. Photos or existing purchase records may be useful when a suffix or replacement choice is uncertain. Product details, payment method, and shipping arrangement can then be reviewed together before order processing.