FESTO DHWS-40-A 1310184 Angle Gripper
The FESTO DHWS-40-A, part number 1310184, is a angle gripper. The supplied Festo datasheet confirms this product identity and lists its model-specific technical data below.
Description
FESTO DHWS-40-A 1310184 Angle Gripper
The FESTO DHWS-40-A, part number 1310184, is a angle gripper. The supplied Festo datasheet confirms this product identity and lists its model-specific technical data below.
Key Features
- Size: 40.
- Max. replacement accuracy: ≤0.2 mm.
- Max. opening angle: 40 deg.
Technical Data
| Brand | FESTO |
|---|---|
| Model | DHWS-40-A |
| Part number | 1310184 |
| Product type | Angle Gripper |
| Size | 40 |
| Max. replacement accuracy | ≤0.2 mm |
| Max. opening angle | 40 deg |
| Rotationally symmetrical | ≤0.2 mm |
| Repetition accuracy, gripper | ≤0.04 mm |
| Number of gripper jaws | 2 |
| Mounting position | Any |
| Mode of operation | Double-acting |
| Gripper function | Bracket |
| Design | Lever |
| Position detection | Via proximity switch |
| Operating pressure | 2 bar … 8 bar |
| Max. operating frequency of gripper | ≤3 Hz |
| Min. opening time at 0.6 MPa (6 bar, 87 psi) | 63 ms |
| Min. closing time at 0.6 MPa (6 bar, 87 psi) | 96 ms |
| Operating medium | Compressed air to ISO 8573-1:2010 [7:4:4] |
| Note on operating and pilot medium | Lubricated operation possible (in which case lubricated operation will always be required) |
| Corrosion resistance class CRC | 1 – Low corrosion stress |
| Ambient temperature | 5 °C … 60 °C |
| Total gripping torque at 0.6 MPa (6 bar, 87 psi), opening | 1497 Ncm |
| Total gripper torque, closing, 0.6 MPa (6 bar, 87 psi) | 1362 Ncm |
| Mass moment of inertia | 3.81 kgcm² |
| Max. force on gripper jaw Fz static | 200 N |
| Max. torque at gripper Mx static | 13 Nm |
| Max. torque at gripper My static | 13 Nm |
| Max. torque at gripper Mz static | 13 Nm |
| Product weight | 775 g |
| Type of mounting | Either: Via female thread and centring sleeve Via through-hole and centring sleeve |
| Pneumatic connection | G1/8 |
| Material cover cap | PA |
| Material housing | Wrought aluminium alloy Hard anodised |
| Material gripper jaws | High-alloy steel |
Application Notes
Confirm the complete model and part number against the existing equipment. Products in the same Festo series may have different dimensions, connections and operating configurations.
Selection and Installation
Check the equipment documentation and the applicable Festo installation instructions before replacement or commissioning.
Inquiry
For a quotation, provide model DHWS-40-A, part number 1310184, required quantity and destination.
Exact-Model Datasheet Check
The supplied Festo datasheet identifies DHWS-40-A as a angle gripper under part number 1310184. It lists size as 40. Confirm the full variant before ordering.
Functional Check After Replacement
After fitting the replacement, follow the equipment commissioning procedure before returning the machine to normal operation. Where applicable, test under controlled conditions and observe response, movement, signals, leakage, and connection stability. Check the installation again after its initial run to identify any adjustment that may be needed.
Payment Arrangements
The payment method is confirmed as part of the order arrangement. International orders may be settled in USD by T/T, PayPal, or another mutually agreed method. For payments in RMB within mainland China, Alipay QR code and WeChat Pay QR code arrangements are also available. The applicable option is agreed before order processing.
Additional information
| Brand | FESTO |
|---|---|
| Model | DHWS-40-A |
| Part number | 1310184 |
| Product type | Angle Gripper |
| Size | 40 |
| Max. replacement accuracy | ≤0.2 mm |
| Max. opening angle | 40 deg |
| Rotationally symmetrical | ≤0.2 mm |
| Repetition accuracy, gripper | ≤0.04 mm |
| Number of gripper jaws | 2 |
| Mounting position | Any |
| Mode of operation | Double-acting |






